|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
ADJUSTMENT INSTRUCTION
1. Application Object
These instructions are applied to all of the color TV, MC-036A. (RF: PG50Ch or A/V input: RED pattern) (4) Loosen fixed screw of DY and closely to CPT funnel part. (5) Check the center of screen that purity magnet of CPT by crossing adjustment. At this time, 4 & 6 pole magnet is located to magnet of nothing. (6) Move the DY to make equal red on whole screen and it does not to make the DY by fixed screw after check a simple color of Red/Green/Blue and white raster whether or not it is a pollution of color. (At this time, take care raster of screen and DY must fixing in the condition which maintains a horizontality.) (7) Check the TV set by move direction.
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order.But the adjustment can be changed by consideration of mass production. (3) The adjustment must be performed in the circumstance of 25±5°C of temperature and 65±10% of relative humidity if there is no specific designation. (4) The input AC voltage of the receiver must keep 220V±10% in adjusting. (5) The receiver must be operated for about 15 minutes prior to the adjustment.
4-2. Convergence adjustment
These adjustments can the best condition of focus after finished purity adjustment. (1) Receive the signal of cross hatch that color is black. (2) Adjust brightness and luminosity till dot appear 9 ~12. (3)Open angle of the two tab of 4 pole magnet by isogonic angle and accord with vertical line of red and blue color in the middle of screen. (4)Maintain as angle of 3) and rotate the tab to accord with vertical line of Red and Blue color in the middle of screen. (5) Open angle of the two tab of 6 pole magnet by isogonic angle and accord with vertical line of Red/Blue and Green. (6) Maintain as angle of 5) and rotate the tab to accord with horizontal line. In case of twisted horizontal line,repeat adjustment of 3) ~ 5) remembering the movement of Red/Green/Blue color. (7) Move the DY to best condition of convergence and attach the CPT to a rubber-chock for fixed DY.
3. Focus adjustment
1. Preliminary steps
(1) Tune the TV set to receive a digital pattern. (SVC mode: Automatically mode change the STANDARD MODE)
2. Adjustment
(1) Adjust center focus volume of FBT for the best focus of vertical line (B). (2) Adjust the upper focus volume of FBT for the best focus of area (A). (3) Repeat above step 1) and 2) for the best overall focus.
4-3 Screen voltage adjustment
1. Preliminary steps
(1) Turn on the TV set. (2) This adjustment should be performed after warming up for more than 15 minutes.
2. Adjustment
(1) Adjust in RF non-signal. (2) Press the ADJ key of SVC remote controller to make horizontal line.
5. White balance adjustment
4. Purity & Convergence adjustment
4-1. Color purity adjustment
(1) Magnetic room set to destination magnetic and horizontal magnetic set to zero. (2) It makes CPT or CABINET enough to demagnetization. (3) Self-adjustment: Adjust by input of Green raster signal Manual-adjustment: Receive the signal of red raster.
This adjustment should be perfomed after screen adjustment. This adjustment set the self-adjustment rule.
1. Test Equipment
(1) Automatic White balance meter: Incase of self-adjustment (2) White balance meter(CRT Color Analyzer, CA-100): 1 EA (3) A SVC remote controller.
-8-
|
|
|
> |
|
